-
A support assembly is made up of a crossarm, including two leg clamps and two crossarm clamps, and two complete legs. Support assemblies are installed underneath a ramp and are used to connect two individual ramp sections. -
Stringers are shaped like an upside-down letter "F" and enclose all Rampit USA ramps and platforms. On platforms, two of the four stringers are usually flipped upside-down to create a smooth transition on and off the platform. Platform stringers are cut at 45-degree angles, whereas ramp stringers are cut at 90-degree angles. Stringers are sold individually and cut to the length specified. For a matching set, please add two of the same size to your cart. -
Square ends are used to enclose and terminate the end of a handrail when space may be an issue. Square ends are sold individually and include pre-installed aluminum inserts (not pictured). Rampit USA recommends using ANSI loops whenever space allows. -
Small bolt packs include all necessary hardware for attaching a set of handrails (four handrails posts) to a ramp or platform:- (8) 1" x 5/16" Carriage Bolt
- (4) 2" x 5/16" Carriage Bolt
- (12) 5/16" Washers
- (12) 5/16" Hex Nuts
-
Rampit USA rubber threshold ramps provide safe and easy access to areas with a rise of up to two inches and can withstand weights up to 1,000 lbs.- 100% recycled rubber can withstand a lifetime of indoor and outdoor use.
- Easy to clean, anti-slip surface for safety and convenience.
- Comes with a hassle-free, lifetime manufacturer's warranty.
- All Rampit USA Rubber Threshold Ramps are ADA Compliant and Made in America.
-
Ramp handrails are sold as a set and specifically designed to fit Rampit USA Independence Series Ramps. Ramp handrails are actual size measured from end to end. Each handrail (2 per set) includes two handrail posts and two filler tubes for lengths 4' - 8' or three handrail posts and four filler tubes for lengths 9' and 10' only. Ramp Handrails include a small bolt pack for installation. Square ends, ANSI Loops, Knuckles, Corners, Caps, and inserts needed for terminating or changing handrail direction are all sold separately. -
Post caps are sold individually and fit securely into the open ends of handrails or legs. Handrails utilize 1 1/2" post caps, while legs utilize 2" post caps. -
Platform handrails are sold individually and specifically designed to fit Rampit USA Platforms. The actual length of each handrail, measured end to end, is shown in the chart below. Platform handrails include two handrail posts and two filler tubes for lengths 4' - 8' or three handrail posts and four filler tubes for lengths 9' and 10'. Platform handrails do not include ninety-degree corners or plastic knuckles for connecting multiple handrails.Handrail Length Actual Length 4' 3' 4 1/2" 5' 4' 4 1/2" 6' 5' 4 1/2" 7' 6' 4 1/2" 8' 7' 4 1/2" 9' 8' 5" 10' 9' 5" -
Plastic knuckles are inserted directly into the open end of two handrail components to create a corner that may not be exactly 90-degrees. -
All Rampit USA aluminum ramps and platforms are assembled using a series of inter-connected pieces of light and/or medium tread. Medium tread is sold by the foot and comes standard in all Rampit USA ramps and commercial platforms. Please note: there are two different types of medium tread in all Rampit USA ramp sections. The first piece of tread is open on the front and the back and is known as starter tread. All remaining tread on a ramp section is standard medium tread, which is open on the front but closed on the back. When ordering, please select the type of tread, the length needed, and the quantity. For standard platform tread, please see light tread. Please contact us for custom lengths not listed below. -
Light tread is sold by the foot and comes standard on all residential platforms and portable ramps. When ordering, please select the length of tread needed and the quantity. For ramp tread, please see medium tread. Please contact us for custom lengths not listed below. -
Legs are sold individually and include a 2" aluminum tube, footpad, and post cap. Rampit USA recommends purchasing legs longer than the needed application to allow for adjustments. We also recommend a diagonal brace for legs exceeding 48" in height.